How do I enable EZCloud?
For NVRs Go to the Web interface of your device and click Setup > Network > EZCloud. Make sure EZCloud is enabled and the device status is online. If the device status is displayed as Online, the device is connected to the EZCloud server; if displayed as Offline, the device is disconnected from the EZCloud server.
How do I access Uniview remotely?
Check whether the device you want to access is bound to your cloud account:
- Open your Web browser, go to en.ezcloud.uniview.com and then log in. The device should be.
- to add it (see Add a Device), or add it.
- on the App (see Add Devices).
How do I view UNV NVR remotely?
How To View A Uniview NVR Via EZView App
- We will be going through this process via the web interface on internet explorer from a local PC.
- First, open the app, then click the 3 Horizontal Line icon in the top left corner.
- Click on Devices.
- Select Add.
- Choose Scan.
- Then Scan the QR Code from the web interface of the NVR.
What is EZView?
EZView is a mobile surveillance app. With this app you can access Uniview surveillance products through network and view live or recorded video, receive alarms and manage cloud devices using your mobile phone.
How do I add a device to EZCloud?
How do you reset an UNV device?
Press and hold the Reset button (the crescent moon button) located below the Power button for 10+ seconds. The device will take up to 60+ seconds to restore the default configuration and return to the original factory version.
How can I access NVR over Internet?
To connect a DVR/NVR to the internet or configure a DVR/NVR for remote viewing, first and foremost, connect your DVR/NVR to your network router either via Ethernet cable or wirelessly. Network–enabled DVRs could be configured for remote viewing. Port forwarding is the key to remote viewing and remote access.
How do I update my EZView app?
First open your EZ View App, tap the main menu, tap on the devices tab, refresh the list of devices by scrolling your finger down the screen, and a red dot will appear on any device that has a firmware upgrade available. Tap on that device, tap on P2P Upgrade and tap Start Upgrade!
How do I set up ezDDNS?
To set up ezDDNS in a DVR or NVR Connect the DVR/NVR to a broad band modem or router, connected to the internet. 2. Assign an IP address to the DVR/NVR within the address range of the router or modem. Go to Network settings in the menu toolbar.
How do I factory reset my UNV camera?
Use the reset switch on the camera’s board. Press and hold the reset button for 20 seconds, then release. The camera will reboot and go back to factory settings. Caution: using the switch to reset the password on a camera will factory default the camera.
What is the default IP address of UNV NVR?
The default static IP address of the camera is 192.168. 1.13, and the default subnet mask is 255.255. 255.0.
Can NVR connect to WiFi?
If a CCTV DVR or NVR don’t have a built-in WiFi support, then you have to run internet cable ( CAT 5 or CAT 6 Ethernet cable ) to connect your DVR or NVR to the internet via the router. Of course, by using another WiFi router/access point as a wireless bridge, you could connect a CCTV DVR to your router wirelessly.
How download video from EZView?
To save a video clip, tap the “video camera” icon (second icon from the left) to mark the beginning of your recording. Let the video play out until you want the recording to end, then tap the “video camera” icon again. Both snapshots and clips are saved to the “Picture and Video” section of EZView.
How do I change my EZView password?
Via EZView App. Click the three lines in the top-left of the screen, this will bring out a pop-out menu. Select Local Config which should be the second option from the bottom. In the configuration screen, select the Forget Device Password which is also the second option from the bottom.