What is Spandek COLORBOND?
Description. A modern, simple square-corrugated roofing and walling cladding that is strong, impact resistant and economical – ideal for both commercial and residential applications. Highly serviceable roofing and walling cladding. Bold ribs offer high strength and high water carrying capacity. Nominal cover width: …
What is the minimum pitch for Trimdek roofing?
2 degrees
Trimdek. Requiring only a minimum pitch of 2 degrees Trimclad® roofing and walling is a preferred choice for commercial and industrial uses.
What is Spandek?
SPANDEK® is pierce-fixed to timber or steel supports. This means that fastener screws pass through the sheeting. You can place screws for SPANDEK® through the crests or in the valleys. To maximise roof watertightness, always place screws through the crests. For walling, you may use either crest or valley-fixing.
How much is Trimdek per meter?
Colorbond Trimdek® Roof Sheet $18.50 L/m | Queensland Roofing Warehouse.
Can Spandek be curved?
spandek, longline 305, CUstoM orb aCCent, CUstoM orb and CUstoM blUe orb can be spring-curved for an arched roof.
What is Klip Lok roofing?
Description. Strong, versatile long-length roofing or walling. The concealed fastening method enables its use on many applications from low pitched roofs to vertical or horizontal ribbed walling. Fixing clips secure sheets without puncturing. No exposed fasteners for clean, smooth lines.
How far can you span Trimdek?
To view the limit state wind pressure capacity tables Download LYSAGHT TRIMDEK® Design and Installation Guide. Table data is based on supports of 1mm BMT….Span Table.
| Types of Span | BMT (mm) | |
|---|---|---|
| 0.42 | 0.48 | |
| End Span | 1300 | 1850 |
| Internal Span | 1900 | 2600 |
| Unstiffened Eaves Overhang | 150 | 200 |
What is Trimdek?
lysaght trimdek® is a subtle square-fluted steel cladding, available in long lengths, so on most jobs you can have one sheet from ridge to gutter without end laps. lysaght trimdek is made of high strength steel and despite its lightness, provides excellent spanning capacity and remarkable recovery after deformation.
Is Trimdek a colorbond?
LYSAGHT TRIMDEK® is a subtle square-fluted steel cladding, available in long lengths, so on most jobs you can have one sheet from ridge to gutter without end laps.
What is the nominal minimum radius for corrugated iron?
Design flexibility – expands the versatility of traditional corrugated roofing by increasing flexibility of design. Variety of shapes – can be formed into a wide variety of curved shapes and radii down to a nominal 500mm minimum.
How wide is Trimdek?
What is the sheet cover of the Trimdek Sheets? The cover width is 762mm. The actual sheet width is 820mm.
How much should a corrugated roof overlap?
An overlap of 150mm is often recommended for roofs with 10° pitches, whilst 300mm is recommended for 5° pitches. Always allow for an overhang of at least 60-70mm so that water can run off without coming into contact with rafters or purlins, which can lead to damp and structural weakness.
How do I stop water running under my flat roof?
At the gutter edge of the roof, install a pre-formed foam filler between the roof sheet and the gutter flashing. This will act as a physical water barrier. Install a profile filler at the highest points under a ridge cap or apron flashing to stop water ingress into the building.
Do you need guttering on a flat roof?
Most modern flat roofs are covered by a membrane that prevents water leaking into your property. But if your roof has a slight slope it will need gutters to ensure proper drainage.
What is spandek®?
SPANDEK® 1 Highly serviceable roofing and walling cladding 2 Bold ribs offer high strength and high water carrying capacity 3 Nominal cover width: 700mm 4 Minimum roof slope: 2°*
What is trimdek®?
TRIMDEK® 1 Long spanning cladding permitting wide support spacing 2 Can be used with TRIM-KLIP™ end and expansion joint system 3 Nominal cover width: 762mm 4 Minimum roof slope: 2°
What is the thickness of trimdek roof trim?
Trimdek 1 762mm Coverage 2 Minimum roof slope: 2° 3 Custom Cut 4 available in 2 thickness .42bmt & .48bmt
Why choose Lysaght spandek® cladding?
With the Tropical Health Research Facility at James Cook University’s Townsville campus set to make a vital impact on global tropical health and disease control, the architecturally striking building is creating visual impact – and will resist debris impact – thanks to the proven strengths of LYSAGHT SPANDEK® cladding.