What is the OSHA Subpart for fall protection?
1926 Subpart M – Fall Protection | Occupational Safety and Health Administration.
What are the three parts of a fall protection system?
Body harness, Anchor, Lifeline Explanation A body harness, anchor, and lifeline are all components of a personal fall arrest system and each have specific requirements as laid out in OSHA 29 CFR 1926.502(d).
What is the subpart for fire protection and prevention?
1926 Subpart F
1926 Subpart F – Fire Protection and Prevention | Occupational Safety and Health Administration.
How many types of fall protection are there?
three different types
While there are a series of questions you can ask yourself to assess the safety of your team while working at height, there are three different types of fall protection systems: elimination, prevention, and arrest.
Which of the following are types of fall protection?
The basic types are guardrails, travel-restraint, fall-restriction, fall-arrest, and control zones.
- 1) Guardrails.
- 2) Travel-restraint system.
- 3) Fall-restriction system.
- 4) Fall-arresting system.
- 5) Control zone.
What are the three types of scaffolds?
Workers who use scaffolds can be divided into three groups:
- Suspended Scaffolds.
- Supported Scaffolds.
- Aerial Lifts.
What are the components of an active fall restraint system?
A personal fall arrest system incorporates four critical components—anchorage, full-body harness, lanyard, and connectors—to safely decelerate and halt a free-falling worker before he impacts a surface below.
What are the main types of fall protection?
The basic types are guardrails, travel-restraint, fall-restriction, fall-arrest, and control zones.
What is OSHA Subpart C?
OSHA 1926 Subpart C General health and safety requirements such as: first aid, fire protection, housekeeping, illumination, sanitation, and personal protective equipment are covered in sections 22 through 28.
What is the Subpart K?
Subpart K – Alternative Requirements for Hazardous Waste Determination and Accumulation of Unwanted Material for Laboratories Owned by Eligible Academic Entities.
What is the general industry Subpart for fire protection?
1910 Subpart L – Fire Protection | Occupational Safety and Health Administration.
What are examples of fall protection?
fixed barriers (e.g., handrails, guardrails) surface opening protection (e.g., covers, guardrails, etc.) warning barriers/control zones. fall or travel restraint systems (i.e., a system to prevent a worker from falling from a work position, or from travelling to an unguarded edge from which the worker could fall)
What are the parts of a scaffold?
Seven Fundamental Parts of a Scaffold
- Base Plates & Jacks. Source: www.rmcspl.co.za.
- Standards (Uprights, Verticals, Legs) Source: www.victoriascaffolding.com.au.
- Ledgers (Runners) Source: www.upload.ecvv.com.
- Transoms (Bearers, Putlogs)
- Boards (Decks, Battens, Planks)
- Couplers (Clamps, Fittings, Clips)
- Braces.
What is fall protection equipment?
Scaffolds, handrails, barriers and movable platforms can be constructed to protect workers employed at heights. Where these devices are impractical, personal fall protection equipment such as full body harnesses, lanyards and retractable lifelines may be used.
What are the guidelines for fall protection?
– Should be able to withstand force of at least 200 pounds. – Should be constructed of materials that will not puncture skin or snag clothing. – Should not use steel or plastic bands for top or middle rails. – Mid-rails and screens, where there is no wall, should be at least 21 inches high.
What are OSHA guidelines for fall protection?
Providing working conditions that are free from known dangers.
What is the OSHA regulation for fall protection?
1910.140 (c) (22) Personal fall protection systems must be worn with the attachment point of the body harness located in the center of the employee’s back near shoulder level. The attachment point may be located in the pre-sternal position if the free fall distance is limited to 2 feet (0.6 m) or less. 1910.140 (d)
What height does OSHA require fall protection?
OSHA provides specific rules to address the hazards of falls from height, including the height at which fall protection is required – four feet for general industry, six feet for construction, 10-feet for scaffold erection, 15-feet for steel erection and whenever employees are working over dangerous equipment/machinery at any height.