What is the first thing you do when using a forklift?
Before starting the forklift, make sure your seat belt is fastened and you can reach all of the controls to drive the forklift. When turning a corner, go slowly and use your horn to let pedestrians and other forklift operators that you are on the other side of the corner. This action can help prevent any collisions.
What is something you should not do on a forklift?
Forklift operators should never:
- Raise or lower loads while the forklift is moving and especially not while turning because it makes the forklift very unstable.
- Allow anyone to stand underneath or right next to raised forks.
- Carry a load with only one fork as it stresses the carriage.
What to know about driving a forklift?
Know the height of your forklift and the load you are carrying. Make sure you can clear the overhead obstacle before proceeding. Keep Loads Low – While driving with a load, you want to keep the forks as low to the ground as possible, while maintaining the stability triangle.
What should you always do before reversing the forklift?
Reversing The Forklift
- When reversing the forklift, always do so slowly.
- Be sure to sound your horn before you reverse to alert pedestrians and other vehicular traffic of your presence.
- When manoeuvring down a ramp, you should always do so in reverse.
Do and don’ts for forklift?
The 5 Dos and Don’ts of Forklift Safety
- Do Drive Responsibly. Just like driving a car on the road, you should always operate your forklift at a speed that will allow you to stop safely.
- Don’t Go Over Your Forklift’s Load Capacity.
- Do Be Aware of Pedestrians.
- Don’t Skimp on Training.
- Do Maintain Your Forklift.
Why do forklifts have 2 breaks?
Its function is twofold. It initially acts as a brake and secondly disengages the transmission, allowing the engine speed to increase or decrease without affecting the drive of the forklift. This process allows the forklift to be slowed or stopped while at the same time allowing the engine speed to be raised.
What position should the forks be in while driving a forklift?
Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back. Use caution when carrying a load on an uneven surface; it creates a tip-over hazard.
How do I prepare for a forklift test?
Prevention is Key For your forklift test, you will need to know to check your mirrors and use the horn. You have to be aware of your surroundings and your speed. You will also monitor foot traffic and load position. Everything requires your full attention.
What do you do when your forklift tips sideways?
If the forklift is tipping over, protect yourself by staying put:
- Stay in your seat and do not attempt to jump off.
- Lean away from the falling direction of the lift.
- Hold onto the steering wheel and make sure you’re stable.
What are the 3 pedals for on a forklift?
There are three types of forklift pedals: accelerator, brake, and clutch. A typical forklift has all three pedals present, but there are exceptions. For instance, some forklifts have an inching pedal that is used to disengage the lift’s transmission and slow down the machine or bring it to a complete stop.
What does the inching pedal on a forklift do?
The purpose of the inching pedal is to disengage the transmission without having to shift the gear lever into neutral every time a lift is performed. This pedal allows you to bring the forklift to a stop or to slow it down.
How to drive forklift for beginners?
Climb into the forklift and buckle the seatbelt. Board the forklift from the left side.
How fast should you drive a forklift?
Develop the knowledge and skill needed to operate forklifts.
Why driving a forklift is different than driving a car?
Driving a forklift is different from driving a car. Operating a forklift requires additional skills and experience because its design makes it less stable and much heavier than cars. Forklifts tip over more easily and are harder to steer and stop. The rear-wheel steering also causes the rear end of the forklift to swing out when it turns.
Where can I learn how to drive a forklift?
Find an OSHA approved training program. Make sure you enroll in a training program that is being taught by a qualified training instructor.